Set your own course in design with the quality, reliability and warranty that accompany all our wraps and graphics. Take control of your table-mounted router for quick, accurate, reliable, and repeatable setups The Precision Router Lift helps you elevate your routing capabilities by providing precise control when making router setup changes or changing bits.With over 250 million cars on American roads, it may seem impossible to express your unique personality or draw attention to a corporate brand. Think again! Wraps installed by our 3M Preferred Graphics Installer create a look that’s anything but ordinary. Choose from our extensive lineup of wraps that span hundreds of colors, finishes and textures, from carbon fiber to psychedelic, and start attracting attention in your sedan, SUV or truck. Llumar precisioncut® system, llumar precisioncut, llumar precisioncut cut software, llumar precisioncut cut, llumar precisioncut cut 4 download. DOWNLOAD LLumar Precision Cut 4.0 Crack Free Download 2020 Youll save time and improve efficiency with our latest, innovative, high-tech film-cutting tool only from.Product brands referenced herein with a or symbol are trademarks of Eastman Chemical Company or its subsidiaries. No Description LLumar Platinum Paint Protection Film, gloss LLumar Platinum Paint Protection Film, matte Dimension m x m m x m m x m m x m m x m m x m 24" x 100' 36" x 100' 48" x 100' 60" x 50' 48" x 100' 60" x 50' LLumar PrecisionCut System LLumar.com 2018 Eastman Performance Films, LLC. FOLLOW THIS GUIDE FOR PROPER PRACTICES & TECHNIQUES Features & benefits Application & storage Film construction Masking sheet 2 mil Removable protective polyester film Clear coat 0.26 mil Flexible, self-healing coating with an advanced hydrophobic surface Urethane 6 mil Impact-resistant 6 mil urethane formulated for excellent UV, heat and water resistance Adhesive 1.2 mil Self-crosslinking acrylic copolymer adhesive formulated for balanced tack, adhesive and cohesive properties Virtually invisible protection from damage caused by rocks, salt, insects and other road debris A proprietary, self-healing clear coat that is scratch and crack-resistant with a high-gloss finish Advanced water resistant surface for increased durability with Hydrogard TM technology Superior optical clarity Ten-year Manufacturer s limited warranty* For detailed product information and installation videos of LLumar Platinum Paint Protection Film visit Recommended installation environment temperature should be within 15.5 C - 32 C (60 F to 90 F) Recommended installation solution (tack solution): 15% of 70% isopropyl alcohol diluted with 85% distilled water Required product storage conditions of 15.5 C - 32 C (60 F to 90 F) Liner 3.5 mil Matte, polyester release liner Product Availablility Mat. LLumar Self-Healing Platinum Paint Protection Film Installation & technical data guide LLumar Paint Protection Film (PPF) offers breakthrough technology for paint protection applications using an advanced, self-healing, solvent-resistant clear coat formulation allowing for easy installation and increased longevity.Our patterns include hoods, bumpers, fenders, mirrors, headlights, rockers, roofs, A-pillars, rear fenders and rear bumpers.2 Technical Data Installation Installation & Removal Performance properties Performance tests are conducted using standard test procedures. Our pattern database for paint protection film is organized by vehicle year, make, model and trim. Helps to minimise liability and quality concerns by eliminating cutting on the vehicle. 01/18 Installers will save time and improve efficiency with our innovative film-cutting tool for paint protection film. No liability is accepted for errors. Visual renderings are for illustrative purposes only actual appearance may vary.
Llumar Precision Cut Software Download 2020 YoullSTAIN TEST 1 ROCK TEST 2 Surface preparation The ideal installation temperature is between 15.5 C - 32 C (60 F to 90 F) Always prep the surface area where the paint protection is applied by using slip solution and cleaning the area of application Use a clay bar to clean and remove dirt or debris from the vehicle paint surface then degrease the installation area using your tack solution Finally, spray slip solution onto the area and using a squeegee, make one final pass to ensure that no fibers were left behind from the towel Tips & tricks If you get a surface scratch in the film, you can use minimal heat to make the film self-heal If you see any debris under the film after installation, you can lift the product with slip solution then reinstall Always squeegee away from an area that has already been installed If there is a colored mark in the film from installation or after, you can remove this with your tack solution Fender installation Remove liner from the film and place the pattern using your slip solution Align your pattern into place and use tack solution if needed to complete your install Bumper installation Remove liner from the film and place the pattern on the bumper with your slip solution Find where the most alignment points are on the vehicle, then use your tack solution to lock into placement (Most of the time the best alignment point is off center of the bumper) Use your tack solution and gently stretch the film as needed toward the wheel to complete the compound curve Repeat on the opposite side Remember to minimize tension around sensors and headlight washers Note: If you are using a piece of film that is not a pattern, follow the same steps After 2 Hours No PPF Applied PPF Applied Hood installation Removal Used Motor Oil NO VISIBLE STAINING Spray slip solution on the hood and film Peel liner and place the pattern on the hood in the correct alignment If needed, use the tack solution underneath the film and position one side of the film, then squeegee into position Distribute stretch as needed to reach the opposite side of the hood, then using your tack solution, squeegee out opposite side LLumar Platinum Paint Protection Film can be removed from the vehicle at any time. Eastman does not warrant or guarantee the accuracy or completeness of this information. Recommended installation tools Installation solutions Mirror installation Product Thickness (Total) 7.5 mil (189.4 microns) Thickness (Clear Coat) 0.26 mil (6.5 microns) Thickness (Base Film) 6.0 mil (152.4 microns) Thickness (Adhesive) 1.2 mil (30.5 microns) Thickness (Liner) 3.5 mil (88.9 microns) Peel Adhesion 72 oz/in (804 N/m) ASTM D3330 Yellow Turbo Black Tube Squeegee Detailing Squeegee Johnson s Baby Shampoo Distilled Water 70% Isopropyl Alcohol Olfa Knife (2) Spray bottles Lint-Free Towels Clay Bar Slip Solution - One bottle (32 oz) of distilled water with two-three droplets of baby shampoo Tack Solution - 15% of 70% isopropyl alcohol diluted with 85% distilled water (for other ratio recommendations, refer to the technical reference page in this document) Remove liner from the film and place the pattern using your slip solution Use your tack solution to lock the film down in the best alignment position Stretch the film as needed to finish the mirror using your tack solution Note: Do not over stretch film and do not use more alcohol to install this will destroy the adhesive Tensile Strength 5000 psi (34.5 Mpa) ASTM D Elongation at Break >400% ASTM D Chemical Resistance Isopropyl Alcohol No Detrimental Effect ASTM D7244, ASTM D6279 Chemical Resistance Heptane / Hexane / Toluene No Detrimental Effect ASTM D7244, ASTM D6279 Weathering QUV 2500h No Detrimental Effect ASTM G153 Weathering Xenon 2500h No Detrimental Effect SAEJ1960 Weathering Xenon 2500h No Detrimental Effect ASTM G155 Staining 1 Transmission Fluid, Antifreeze, Windshield Washing Fluid, Used Motor Oil, Ketchup, Mustard Acid Immersion 10% Sulfuric Acid 72 hours No Detrimental Effect Base Immersion 10% Sodium Hydroxide No Detrimental Effect Resilient ASTM E Rock Chip Resistance 2 SAE J400 Gravelometer Pass water-worn road gravel, 3/8" to 5/8" mesh Note: All statements, technical information and recommendations herein are based on tests Eastman believes are reliable. Free fantasy rpg games for macThis method may cause the adhesive to split which will require more adhesive to be cleaned off the vehicle. A heat gun or hair dryer can also be used to soften the adhesive. Using the steam removal method, the adhesive stays on the film during removal, requiring less adhesive clean-up. Steam softens the film and makes it easier to remove.
0 Comments
Leave a Reply. |
AuthorPaul ArchivesCategories |